BROOKE-BOARDS HOME IMPROVEMENTBROOKE-BOARDS HOME IMPROVEMENT AND SUPPLY

Change Drill

Safe Installation of Baby Changing Stations

It is always recommended that only a carpenter or a qualified person should perform the installation of baby changing station unit. Changing stations are built with both plastics and metals, thus to insure proper installation and compliance to building codes, baby changing stations must be properly installed according to the manufacturer’s instructions.

Baby changing stations can be either recessed or surface mounted. Both are safe to hold infants and children up to a certain weight. You can choose which model to have installed depending on where you will be mounting it inside your home or commercial restrooms. Safety straps will be included in the station as a safety precaution for moving babies.

Koala Bear Kare® Baby Changing Stations have been tested to hold a static load of up to 400 pounds. To do this, the unit must be properly installed onto a permanent wall that is capable of supporting that much weight, and can accommodate the supplied installation hardware. The Koala Bear Kare® Baby Changing Station meets ADA regulations when properly installed.

Mounting a vertical baby changing stations:

1. Remove the station from the shipping container and check for any freight damage. Identify the best location for installing the baby changing station. Hold the unit in place, open the bed, and make sure that there is adequate operating clearance.

2. Based upon the type of wall on which the unit will be mounted, determine the best method of mounting. Not all of the included hardware may be required for proper installation.

3. The vertical unit has four mounting holes provided in the back wall of the unit, which are positioned on a 16” stud center. If possible, locate the wood or metal wall studs for fastening the baby changing station in the desired location. If the walls do not have studs on center as outlined, make sure at least one side of the unit is installed into the stud. Use toggles (supplied) for holes on the other side.

4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 63” up from the floor (59” ADA), at the center of the stud, and mark the wall. Line up the top left mounting hole with this mark, then use a measuring tape and level to mark the remaining three mounting holes. This will locate the bottom of the station 31” from the floor (27” ADA).

5. If the wall has wood studs on 16” centers, drill 1/8” pilot holes at the marks and use the four ¼” x 3” panhead tapping screws with supplied washers. If the wall is masonry or tile over wood studs, use a 7/32” masonry drill until you hit the stud, then proceed to drill 1/8” pilot holes into the studs and use the four 1/4” x 3” screws with supplied washers.

For more information visit this websites http://www.baby-changing-stations.com

About the Author

If you are looking to buy a baby changing station from an online store then I have a website in mind that stocks baby products and baby changing stations of all types and quality brands. Visit link http://www.baby-changing-stations.com .

How to Use a Hammerdrill : How to Change Hammer Drill Bits

Bring a Revolution to Your Home by Having Cordless Drills Around

With the arrival of some extremely light weight, potent and rechargeable batteries, a radical change has been brought to the way we usually perform our repairing works at home. Even many utility tool-makers have availed the maximum by this surge of batteries and launched the utility tools like cordless drills. Cordless drills bring a sense of convenience along as they lack cords, thus eliminate the tensions of a restricted reach. 

 

Home owners now have their choices with the companies like Ryobi, Skil, Craftsmen, Black & Decker to get what the exact needs call for. Professionals even boast of plenty with the firms like Bosch, DeWalt, and Hitachi to precisely serve their repairing and other common needs. 

 

Out of the available choices in cordless drills, DeWalt cordless drill is way ahead in terms of popularity. DeWalt has a reputation for presenting almost every sort of utility tool, and is dishing out the DeWalt cordless drills for more than a decade. 

 

The type of DeWalt cordless drill to be chosen differs with the nature of the project underhand, as there are many variations available. Cordless drills in general vary with their utility, functions, size, weight, power and so on. With the cordless drills, it's feasible to expect and get different speeds. Lower speeds will be better when working with the harder materials. Even you don't need to bother, as cordless drills have an adjustable clutch to support ever type of drill. 

 

Picking a drill with higher voltages might be a good bet, as you need change with times as the materials used change. So have the power to command any job with an impeccable ease and ability, while using cordless drills.

 

Thinking about the battery to be used in your cordless drills is a fine move, as the life of battery tends to differ with every drill. So giving a try to the cordless drills with Two Batteries has its own merits. This way, you can have one battery spare to be used later on while working with the first one to save you valuable time. 

 

With cordless drills gaining prominence in roughly all current woodwork, metalwork and construction works, possessing an Electric Drill turns out to be quite indispensable for all homes everywhere. The electric drills are even more in style than a manual drill and prove their utility by furnishing simplicity and expediency. 

 

With plethora of options in cordless electric drills to pick from, it's always suggested to get along with the brands rather famous. Moreover, identifying the usage ahead of buying cordless drills has many gains to be reaped while drilling.

About the Author

Smit Mathur is an expert for writting Articles and is currently working for Sydney Tools. For more information related to DeWalt cordless drill, Cordless drills, Drill, Electric drills, Electric Power Tools Please visit http://www.sydneytools.com.au/

[phpbay]Change Drill, 51, "", ""[/phpbay]

Power Change Pilot Drill Bit $4.24 Quick change pilot drill bit for Power Change hole saw system.

Drill $8.99 Drill

Drill Sharpener $199.99 Increased performance and precision with the new Spiral Drill Sharpeners. &#65279Performance features for the new Generation: * super simple Drill positioning * stronger positioning clamps for longer life * excellent grinding of cone coating due to curve-controlled holding chuck * optimised chuck has extended jaws for central clamping * variable jaw length within the same tightening operation * grinding rings easy to change * new generation Motor with permanent magnets ensures constant power, independently of rotation speed or load. Model 500X: Grinding range from approx. 2.513.0mm Point angles 118? and 135?

Skil 90942 42-Piece Quick Change Drill/Drive Bit Set $25.99 Skil 90942 42-Piece Quick Change Drill/Drive Bit Set. Included Quick Change Adapter allows for easy bit changes and fits all brands of drill drivers. 15 Twist Drill Bits ideal for drilling in wood can also be used for drilling in plastic and metal. 14 Insert Bits meet all screwdriving needs for the most common screw heads. Set also includes 6 nutsetters, bit holder, measuring tape and heavy-duty case

Skil 90921 21-Piece Quick Change Drill/Drive Bit Set $19.99 Skil 90921 21-Piece Quick Change Drill/Drive Bit Set. Included Quick Change Adapter allows for easy bit changes and fits all brands of drill drivers. 7 Twist Drill Bits with hex shanks ideal for drilling in wood can also be used for drilling in plastic and metal. 10 Insert Bits for the most common screw heads. Set also includes 5 nutsetters, screw guide and heavy-duty case

12V Extender Drill $72.69 12v vsr extender drill Variable speed reversing drill with 5-position drill head that locks in 5-positions for added versatility 24-position clutch Quick Connect bit change system 3-finger trigger for comfort and control in all positions Kit includes: 1 model No. FSB12 battery, 1 model No. PSMVC charger, 6 drill bits, 4 screwdriver bits, 5 nut drivers, and plastic case Brand #: Black & Decker XD1200K UPC: 028877385488 Keywords: drill 12v extender cordless

17-Piece Drill And Drive $19.79 17pc drill/drive set 17-piece quick change drill driver accessory system for all drills Allows easy bit changes without rechucking Hex shank bits lock in and out of holders Set includes: Quick change holder, 1 each of 7/16?, 3/8?, 5/16? magnetic nut drivers, 1 each of 3/32?, 1/8?, 1/8?, 5/32?, 1/4? hex shank drill bits, (2) 2? Phillips bits, (3) 2? slotted bits, and 2 hex bits Packaged in durable rubber-gripped plastic case Brand #: Do it Best Imports 321244 UPC: 009326321042 Keywords: drill bit set quick change drive

7.2V Cordless Drill $34.58 7.2v cordless drill Keyless chuck for easy bit change Balanced mid-handle design for superior control Fan cooled motor for longer life 2-speed switch with forward and reverse 325/650 RPM Includes charger Brand #: Black & Decker 9099KC UPC: 028877326764 Keywords: cordless drill 7.2v

Rechargeable Drill/Driver 18V $24.99 Westfalia 18 Volt Electronic Rechargeable Battery Powered Drill. With quick-change chuck 1.5-10mm. Accelerator switch. Screw bit. 17-position torque setting with rechargeable battery and charger unit. CE tested.